Maintenance

Creating a turn signal position lamp on/off for a Honda motorcycle...

CBX1000 turn signal position on/off tuning. By cutting Br/W coming out from 8p (8-pole coupler),on/off function can be realized. The same goes for CB900F. When installing the FCR,a thin switch is installed on the right side. I achieved this by using a 4-pole relay to interrupt the wiring.
       
カテゴリCBX1000Maintenance
タグCBX1000LEDYouTube
CBX1000

HONDA CBX1000 Photos 2022-April...

I write explanations and concepts about motorcycles. Basically,there are almost no parts that are not touched. The frame is a little old but has been repainted. The engine has had the paint removed and is in pristine condition. I'm installing Brembo,Ohlins,Dangani,FCR,Uotani,etc. My main tires at the moment are Continentals.
       
カテゴリCBX1000touring
タグBremboCBX1000CNCComstarWheelsFCRLEDTouring
touring

FCR test run,Yasuno Station...

Let's go for a test run after tuning up the FCR! Yasuno Station in northern Hiroshima Prefecture is becoming a secret touring spot,and the number of people is increasing every year. There were a lot of people on bicycles,and I saw people with Shimane license plates here and there. I rarely use it when I want to go for a long test run.
       
カテゴリCBX1000FCRtouring
タグASCBX1000FCRPSTouring
FCR

FCR-SJ Slow Jet – FCR Carburetor Installation...

I will mainly post photos of the FCR being removed and installed. I adjusted the throttle wire, accelerator pump, and idle stop screw.
       
カテゴリCBX1000FCRMaintenance
タグASCBX1000FCRPSVacuumgauge
FCR

FCR-Changed SJ slow jet. 2022-04-15...

Even if I turn only one CBX1000 FCR pilot screw,there is no change in idle. Is it way out of range? Is it a characteristic that we don't notice even though it is changing? I'm not really sure.
       
カテゴリCBX1000FCRMaintenance
タグASCBX1000FCRPS
FCR

FCR-Install SEP bearing guide on CBX1000!...

The CBX1000 FCR has been used for about 20 years. In terms of mileage,I have used it less than 10,000 km,and I use it while replacing rubber parts,packing,Vacuum release plate,etc.
       
カテゴリCBX1000FCRMaintenance
タグCBX1000FCRYouTube
CBX1000

CBX1000 Photos - At Personal Garage - Many Photos...

This is a photo gallery of Personal Garage. This is a fun garage with everything from normal to shiny road glides. Next door is a custom car shop.
       
カテゴリBiker&OthersCBX1000
タグBremboCBX1000CNCCustomFCRLED
Maintenance

Brembo CNC brake caliper installation...

Up front are Brembo CNC axial 2-block calipers titanium hard anodized 40mm. At the back is a Brembo CNC axial 2 block caliper with hard anodized new crab 82mm.
       
カテゴリCBX1000Maintenance
タグBremboCBX1000Ohlins
Maintenance

Replace the exterior with a repainted one...

The exterior is primarily red, with gold and orange lines. There are two types of lines, so be mindful of the details.
       
カテゴリCBX1000CowlMaintenance
タグCBX1000
FCR

Install Quick turn throttle -Active Type3...

Changed the throttle holder from Vito to Active. It went from 90 degrees to 56 degrees. When the accelerator opening is 90 degrees,it is low throttle.
       
カテゴリCBX1000FCRMaintenance
タグCBX1000CustomFCR