CBX1000

HONDA CBX1000 Photos 2022-April...

I write explanations and concepts about motorcycles. Basically,there are almost no parts that are not touched. The frame is a little old but has been repainted. The engine has had the paint removed and is in pristine condition. I'm installing Brembo,Ohlins,Dangani,FCR,Uotani,etc. My main tires at the moment are Continentals.
2022-04-18
       
カテゴリCBX1000touring
タグBremboCBX1000CNCComstarWheelsFCRLEDTouring
touring

FCR test run,Yasuno Station...

Let's go for a test run after tuning up the FCR! Yasuno Station in northern Hiroshima Prefecture is becoming a secret touring spot,and the number of people is increasing every year. There were a lot of people on bicycles,and I saw people with Shimane license plates here and there. I rarely use it when I want to go for a long test run.
2022-04-18
       
カテゴリCBX1000FCRtouring
タグASCBX1000FCRPSTouring
FCR

FCR-SJ Slow Jet – FCR Carburetor Installation...

I will mainly post photos of the FCR being removed and installed. I adjusted the throttle wire, accelerator pump, and idle stop screw.
2022-04-17
       
カテゴリCBX1000FCRMaintenance
タグASCBX1000FCRPSVacuumgauge
FCR

FCR-Changed SJ slow jet. 2022-04-15...

Even if I turn only one CBX1000 FCR pilot screw,there is no change in idle. Is it way out of range? Is it a characteristic that we don't notice even though it is changing? I'm not really sure.
2022-04-15
       
カテゴリCBX1000FCRMaintenance
タグASCBX1000FCRPS
FCR

FCR-Install SEP bearing guide on CBX1000!...

The CBX1000 FCR has been used for about 20 years. In terms of mileage,I have used it less than 10,000 km,and I use it while replacing rubber parts,packing,Vacuum release plate,etc.
2022-04-15
       
カテゴリCBX1000FCRMaintenance
タグCBX1000FCRYouTube
CBX1000

CBX1000 Photos - At Personal Garage - Many Photos...

This is a photo gallery of Personal Garage. This is a fun garage with everything from normal to shiny road glides. Next door is a custom car shop.
2022-04-14
       
カテゴリBiker&OthersCBX1000
タグBremboCBX1000CNCCustomFCRLED
Maintenance

Brembo CNC brake caliper installation...

Up front are Brembo CNC axial 2-block calipers titanium hard anodized 40mm. At the back is a Brembo CNC axial 2 block caliper with hard anodized new crab 82mm.
2022-04-14
       
カテゴリCBX1000Maintenance
タグBremboCBX1000Ohlins
Maintenance

Replace the exterior with a repainted one...

The exterior is primarily red, with gold and orange lines. There are two types of lines, so be mindful of the details.
2022-04-14
       
カテゴリCBX1000CowlMaintenance
タグCBX1000
FCR

Install Quick turn throttle -Active Type3...

Changed the throttle holder from Vito to Active. It went from 90 degrees to 56 degrees. When the accelerator opening is 90 degrees,it is low throttle.
2022-04-13
       
カテゴリCBX1000FCRMaintenance
タグCBX1000CustomFCR
Maintenance

table comstar wheel Polished manual work...

table comstar wheel Polished manual work.From removing the anodized aluminum to the rim and spokes. I can go 200km/h and I went to the circuit. No trouble.
2022-04-13
       
カテゴリCBX1000Maintenance
タグCBX1000ComstarWheels
Next page