Page 16 | CBX-LALALA HONDA Mortorcycle CBX1000 FCR Carburetor

What is the appeal of motorcycle carburetor specifications?...

There are two types of motorcycle fuel injection systems in the world. Carburetor specifications or other than Carburetor specifications? Except for the carburetor specifications,it will be injection. Since FCR is also a carburetor specification,I will write about the good and bad points of carburetor specifications while comparing them with injection. The trick here is to write about it while comparing it to injection.

2022-08-17

カテゴリ

タグ

FCR tuning - SJ and MJ change - 2022-08-15...

With SJ45,I felt like the screw was opening too much,so I changed it to 42. I chose 42 because I wanted to make fine-tuned tuning,but 40 might be the perfect range for all year round. I feel a little regretful that it might not be necessary to make it look strangely deviate from Bito's initial tuning.

2022-08-16

カテゴリ

タグ

Should I change the taper angle and cut-up of FCR? Check the number of clip stages first....

This time I will write in a column. The other day,I had a little conversation about the FCR tuning with the divine engineer who gave me two engines for my CBX1000 free of charge. I was told,``JN checks the number of clip stages before checking the taper angle.'' According to the master,it's natural that the clip position will change if you change the taper,so if you don't take that into account when purchasing a jet needle,it will be a waste of money.

2022-08-09

カテゴリ

タグ

FCR tuning - AS air screw adjustment - 2022-08-03...

I wanted to eat curry for lunch,so I went for a light FCR test run. With my ability,I can't decide on a good screw position in one go,so I just do test runs and try different screw positions from rich to lean.

2022-08-03

カテゴリ

タグ

Photos of CBX1000 cowl specifications are posted....

Even if it is not a CBX1000 cowl specification,some parts may be helpful for owners who want to install a frame-mounted cowl on a naked specification motorcycle. This is a duplicate of the previous article,but the content posted a while after installation and the post immediately after installation are slightly different.

2022-08-01

カテゴリ

タグ

FCR tuning - screw adjustment and AS Uotani SP2 dial tuning - 2022-07-29...

I looked at the cold startability of the engine and tried adjusting AS and PS. I had already decided on the general tuning the other day,so I didn't have to spend any particular time on it,so it was more of a confirmation process. I feel that it is better to open the PS for starting performance. I tried tightening and opening it,but in the end I left it at the default tuning and moved the idle stop screw a little higher.

2022-07-29

カテゴリ

タグ

FCR tuning - AS and PS adjustment during test run - 2022-07-28...

If you try to improve the starting performance,the PS will tend to open. Since it is a racing cab,you may not need to worry too much. Either way,I currently prefer a richer shade,so I'll see how it goes tomorrow morning. I'm thinking about various things,such as tightening the PS a little more and raising the stop screw a little.

2022-07-28

カテゴリ

タグ

FCR - JN clip stage number change - 2nd time today - 2022-07-27...

The goal of the tuning was to improve the adjustment range for the pilot screw and air screw, as it seemed to be nearing its limits. I responded by increasing the size of the slow jet (SJ). It seemed to be working fine as it was, but I prefer tuning it richer. After changing the SJ, I re-synchronized and checked the throttle cable tension. Since there haven’t been significant changes since the last adjustment, I was able to complete it quickly.

2022-07-27

カテゴリ

タグ

FCR - Test run - Mesh jacket is pretty good - 2022-07-27...

It's a cool mesh jacket when you look at it alone,but I feel like it doesn't go well with the CBX1000. It may be suitable for bright tricolor replicas such as NSR. Since I have already purchased it,I will be spending the summer with a mesh jacket for the time being.

2022-07-27

カテゴリ

タグ

FCR tuning - PS pilot screw changes - 2022-07-25...

The other day,I found out the scope of responsibility for PS Pilot Screw! That's what I was feeling,so I went for a test drive and checked the air-fuel ratio while turning the PS. About the throttle opening - It's around 15 when fully closed and around 12.5 when it's around 1/16-1/8. Is around ①14 good when fully closed and idling? ②Is around 12.5 good? That's the idea.

2022-07-26

カテゴリ

タグ