"jet needle"

FCR

FCR - tuning - 2022-06-10

This article is about the test run and turning after changing the light dial of AS Uotani SP2. This is a tuning change due to a change in ignition timing. I was thinking of dealing with it by changing the accelerator pump or clip. However,I think it is better not to include the acceleration pump as the main tuning item.
2022.06.11
       
カテゴリCBX1000FCR
タグAS-Uotani-SP2CBX1000CBX400FFCRFCR-BeginnersJN
FCR

FCR tuning - Jet Needle - 2022-06-02...

CBX1000 FCR turning. This is a story about changing JN and changing clips after tuning in. The other day,I touched the oil level,removed the SJ,and touched it a lot,so I checked the synchronization of the 6 cylinders of the FCR once just to be sure. Honestly,it was at a level where I didn't have to touch it much.
2022.06.03
       
カテゴリCBX1000FCRMaintenance
タグCBX1000FCRFCR-BeginnersJNVacuumgauge
FCR

FCR Tuning - Slow jet changed from 48 to 55 - 2022-05-23...

Changed FCR's SJ slow jet. The number has been changed from SJ-48 to SJ-55. The intention is to bring the fixed AS to around 1.0 to 1.30 minutes by reversing P1.15 minutes. I've put #52 in SJ,so I'm predicting that unless I put in at least #55,AS won't be around 1.30 minutes back,so I'm raising the number all at once.
2022.05.24
       
カテゴリCBX1000FCR
タグASCBX1000FCRFCR-BeginnersPS
FCR

Jet needle clip change - 2022-05-18...

I was concerned about the blowout being about 1/2,so I changed the number of clip stages. The current FCR jet needle is 90FTR #2,and I was planning to touch the AS air screw from time to time. The vacuum gauge uses two Daytona 4-gauges to create a CBX1000-spec 6-gauge.
2022.05.18
       
カテゴリCBX1000FCR
タグASCBX1000FCRFCR-BeginnersJNVacuumgauge
FCR

FCR-tuning JN - 2022-04-23 - Video available...

Continuing from the other day,I will touch on JN. If it goes out of control in the same season and in the same place,I think it's better to think that something is broken in the first place. I work with the mindset that if something goes wrong,I can just get things back to normal.
2022.04.24
       
カテゴリCBX1000FCR
タグCBX1000FCRFCR-BeginnersJNYouTube
FCR

FCR - tuning JN - 2022-04-22...

Regarding the FCR turning,the JN-Jet Needle's clip seems to change the way it blows up. The position of the clip is lean at the top and rich at the bottom. It's better to choose based on feel,without worrying about the air/fuel ratio.
2022.04.22
       
カテゴリCBX1000FCR
タグCBX1000FCRFCR-BeginnersJNVacuumgauge
FCR

PLX-DM6-Air fuel ratio meter-A/F meter installation...

I think Autogauge,PLX,and Innovate are the options for air-fuel ratio meters. I used Autogauge and PLX. In terms of visibility,the auto gauge is completely invisible during bright daytime hours. PLX has faster startup speed.
2022.04.21
       
カテゴリCBX1000FCRMaintenance
タグCBX1000FCRFCR-Beginners
FCR

FCR-SJ Slow Jet – FCR Carburetor Installation...

I will mainly post photos of the FCR being removed and installed. I adjusted the throttle wire, accelerator pump, and idle stop screw.
2022.04.17
       
カテゴリCBX1000FCRMaintenance
タグASCBX1000FCRPSVacuumgauge