Page 11 | CBX-LALALA HONDA Mortorcycle CBX1000 FCR Carburetor

Buying a CBX1000 FCR - How to tune for the first time...

Many people want to install a racing carburetor on the CBX1000. In Japan,the options are the BITO FCR or CRS carburetor. It seems that TMR can also be made to order,but it is not common. If I were to buy one,I would choose the FCR.

2022-11-16

カテゴリ

タグ

FCR Tuning - Jet needle changed to 90FTN. I was concerned about the straight diameter - 2022-11-15...

This is a test run after changing the jet needle of the CBX1000 FCR. The purpose is to check whether the straight diameter of the jet needle is good or bad at low throttle opening. I have been selecting a jet needle for the slow jet 48 for a while now. As a result of the test run,the acceleration is so good that I don't want to touch it for a while.

2022-11-15

カテゴリ

タグ

FCR - The fuel line should be angled so that fuel can flow easily....

CBX1000 is a forced open/close type gasoline cock. About the fuel line Although it is a short path during the process of sending fuel from the gasoline tank to the carburetor,air may become trapped. It's not just the angle of the fuel line,but also the nature of the filter that makes it difficult for fuel to flow.

2022-11-15

カテゴリ

タグ

FCR Tuning - Adjust the air screw with a digital tachometer - 2022-11-10...

Fine adjustment of the air screw and pilot screw positions. Until now,we had determined the position of the air screw based on a test run. Of course,I also use the air-fuel ratio meter as a reference. The position of the air screw is determined based on a test run. I purchased a digital tachometer.

2022-11-10

カテゴリ

タグ

Notes on changing FCR slow jet...

Since the CBX1000 has 6 carburetors,the number of jet changes is 6 times that of the SR,and 1.5 times that of a 4-cylinder motorcycle. It's a pain. When purchasing a new jet,it costs 6 times more than an SR. I don't regret it too much since it's money I'll be spending on my hobby,but it's better if it doesn't cost anything.

2022-11-10

カテゴリ

タグ

FCR tuning - Jet needle replacement - Up change - 2022-11-08...

This is the FCR tuning. Current jet needles have a special thread count that sharpens up. It should be 90FXM#3=90FTM#1. I haven't tried it,so I don't know,but it should probably be the same. I'll check it out when I have some free time.

2022-11-08

カテゴリ

タグ

FCR Tuning - Tuning throttle opening from 1/16 to 1/8 - 2022-11-06...

Regarding the current FCR tuning of CBX1000,I was concerned about the lower throttle opening. It's not a good idea to get caught up in the air-fuel ratio meter,but a partial reading of 10.5 is around throttle opening of 1/16 to 1/8. It is unclear whether this condition is good or bad.

2022-11-07

カテゴリ

タグ

FCR Tuning - The number of clip stages of the jet needle is determined by the driving feeling...

You can enjoy changes in the driving feeling that cannot be seen only with lean or rich FCR influence range. When you wear an air-fuel ratio meter,you tend to look at the numbers and judge whether it's lean or rich.Considering the characteristics of engine revving,etc.,there are some areas that are difficult to show in the numerical values. Simply put,you can change the number of clip stages one by one and try the number of stages that gives you the driving feeling you like.

2022-11-04

カテゴリ

タグ

FCR tuning - Carburetor synchronization work - 2022-11-02...

I had time,so I did some synchronization work on the CBX1000's FCR carburetor. If you play around with the idling stop screw,you will notice a difference between the carburetors in groups 1,2,and 3 and the carburetors in groups 4,5,and 6,which is a concern. Recently,I have been focusing on tuning the throttle to a low opening.

2022-11-02

カテゴリ

タグ

FCR Tuning - Slow Jet Selection - Start with the pilot screw back at about 1.0 turn...

You should be careful when choosing a jet needle. Even if the condition is good when the throttle opening is low,the effect may appear as the throttle opening is increased. The number of CBX1000's FCR jet needles at the time of shipment is 90FXM#3. The cut-up is special.

2022-11-02

カテゴリ

タグ