Vacuumgauge

FCR

FCR tuning - AS Adjustment - 2022-06-25...

CBX1000 FCR turning. I adjusted the AS air screw and the PS pilot screw. As I wrote in another article,my current opinion is that there are no surprising changes in PS and AS for each cylinder in the CBX1000.
       
カテゴリCBX1000FCR
タグcabtuningCBX1000FCRFCR-BeginnersVacuumgauge
FCR

FCR - Synchronization - Taper Gauge...

The suction force for each cylinder is slightly different,but even if you just match it with the taper gauge,the synchronization is good. Although it is far from perfect,there are two points below: (1) The engine does not idle at high speeds when it warms up. (2) The tachometer returns extremely poorly when racing.
       
カテゴリCBX1000FCRMaintenance
タグCBX1000FCRFCR-BeginnersVacuumgauge
FCR

FCR-6-synchronization-balanced pipe...

There are three ignition coils in the CBX1000. Why are there three cylinders even though it has six cylinders? Nos. 1 and 6 are fired at the same time. Light 2 and 5 at the same time. This is because No. 3 and No. 4 are lit at the same time.If you write what you want to write early,the balance pipe connections are number 1 and number 6. No. 2 and No. 5. Connect No. 3 and No. 4. The engine firing order is 1-5-3-6-2-4.
       
カテゴリCBX1000FCRMaintenance
タグCBX1000FCRFCR-BeginnersVacuumgauge
FCR

FCR tuning - Jet Needle - 2022-06-02...

CBX1000 FCR turning. This is a story about changing JN and changing clips after tuning in. The other day,I touched the oil level,removed the SJ,and touched it a lot,so I checked the synchronization of the 6 cylinders of the FCR once just to be sure. Honestly,it was at a level where I didn't have to touch it much.
       
カテゴリCBX1000FCRMaintenance
タグCBX1000FCRFCR-BeginnersJNVacuumgauge
FCR

Jet needle clip change - 2022-05-18...

I was concerned about the blowout being about 1/2,so I changed the number of clip stages. The current FCR jet needle is 90FTR #2,and I was planning to touch the AS air screw from time to time. The vacuum gauge uses two Daytona 4-gauges to create a CBX1000-spec 6-gauge.
       
カテゴリCBX1000FCR
タグASCBX1000FCRFCR-BeginnersJNVacuumgauge
FCR

FCR - tuning JN - 2022-04-22...

Regarding the FCR turning,the JN-Jet Needle's clip seems to change the way it blows up. The position of the clip is lean at the top and rich at the bottom. It's better to choose based on feel,without worrying about the air/fuel ratio.
       
カテゴリCBX1000FCR
タグCBX1000FCRFCR-BeginnersJNVacuumgauge
FCR

FCR-SJ Slow Jet – FCR Carburetor Installation...

I will mainly post photos of the FCR being removed and installed. I adjusted the throttle wire, accelerator pump, and idle stop screw.
       
カテゴリCBX1000FCRMaintenance
タグASCBX1000FCRPSVacuumgauge
FCR

FCR synchronization and 6-series vacuum gauge...

Calibration and adjustment of vacuum gauge. Align the synchronization of CBX1000 with 6 vacuum gauges. If you are using a 4-way vacuum gauge,you can easily find out how much the difference is by replacing the numbers 1 and 2 that you normally use.
       
カテゴリCBX1000FCRMaintenance
タグAScabtuningCBX1000FCRJNMJPSVacuumgaugeYouTube