FCR-FCR tuning in general. 6 cylinder tuning, AS, JN, MJ replacement, etc.

Heading to Hattendo Village in Mihara City,Hiroshima Prefecture for a test run of the FCR....

The other day,I replaced my MJ,so I went on a solo tour on the expressway to Hattendo Village,which also served as a test run of the FCR. Hattendo is famous for its cream bread. The facility itself seems to be kept well-maintained,and the staff seemed to be responding well. If you have a flight passing by nearby,Sehito is a facility worth stopping by at least once.

2022.05.23

カテゴリ

タグ

Jet needle clip change - 2022-05-18...

I was concerned about the blowout being about 1/2,so I changed the number of clip stages. The current FCR jet needle is 90FTR #2,and I was planning to touch the AS air screw from time to time. The vacuum gauge uses two Daytona 4-gauges to create a CBX1000-spec 6-gauge.

2022.05.18

カテゴリ

タグ

Scope of influence of FCR's MJ main jet...

I try to keep it between 11.5 and 13.5 during acceleration,and aim for 12.5 to 13.0 as much as possible. I try not to worry about it even if I get into 11 in a partial. I prioritize the experience and try not to worry about the air-fuel ratio even if it reaches a very extreme value.

2022.05.16

カテゴリ

タグ

PINGEL cock flow comparison PINGEL1/4...

I am using PINGEL4000-1/4. I don't know the model name,but I'm using a reserve type with an adapter. In rare cases,there are online shopping sites that have incorrect adapter descriptions or actual sizes. The comparison target is the CBX1000's genuine fuel cock,which is a forced open/close type fuel cock.

2022.05.13

カテゴリ

タグ

Brembo - Corsa Corta installed...

Brembo Corsa Corta installed on CBX1000. Is it better to write brembo's CorsaCorta19RCS? The caliper and master are a combination of flow rates. The front is CNC 4 pot 30/34 40mm. 4 pots with 30mm and 34mm pistons. The diameter of the master is 19.

2022.05.12

カテゴリ

タグ

Test run after installing HONDA CBX400F cowl - air screw adjustment...

It's been a while since I started working on it,so I'd like to get a feel for the FCR. The main thing is to attach the cowl,so I don't want to touch it too much because it will change what I do. I feel like my cornering is going really well.

2022.05.10

カテゴリ

タグ

FCR-tuning JN - 2022-04-23 - Video available...

Continuing from the other day,I will touch on JN. If it goes out of control in the same season and in the same place,I think it's better to think that something is broken in the first place. I work with the mindset that if something goes wrong,I can just get things back to normal.

2022.04.24

カテゴリ

タグ

FCR - tuning JN - 2022-04-22...

Regarding the FCR turning,the JN-Jet Needle's clip seems to change the way it blows up. The position of the clip is lean at the top and rich at the bottom. It's better to choose based on feel,without worrying about the air/fuel ratio.

2022.04.22

カテゴリ

タグ

FCR Carburetor - Throttle Valve Seal Replacement...

Replaced FCR carburetor parts. Around the Throttle vale seal and accelerator pump. I'm thinking about riding CBX1000,so I try to avoid long-term immobility. Many work methods include removing the cab,modifying it at home,and installing it as an Assy. Working in a rental pit.

2022.04.22

カテゴリ

タグ

PLX-DM6-Air fuel ratio meter-A/F meter installation...

I think Autogauge,PLX,and Innovate are the options for air-fuel ratio meters. I used Autogauge and PLX. In terms of visibility,the auto gauge is completely invisible during bright daytime hours. PLX has faster startup speed.

2022.04.21

カテゴリ

タグ