I am writing articles related to CBX1000. The basics are the same whether it's a 6 cylinder or a 4 cylinder! Should be. . .

CBX400F Integra cowl installation completed version...

Completed installation of CBX400F Integra cowl on HONDA CBX1000. The blinker stay and Yoshimura time meter were shaking badly,so I fixed it. The turn signal can be handled by inserting rubber into the bolt joint and adding one stay. The Yoshimura Temperature Meter is swaying,so we wrapped rubber around the part that is in contact with the frame.

2022.05.04

カテゴリ

タグ

CBX400F Integra cowl installation ~Test run~...

The turn signal stay and the Yoshimura oil temperature gauge stay are shaking so badly that they need to be fixed. Regarding the CBX400F Integra cowl,there seems to be no problems with strange vibration or strength. There seems to be no problem with the steering angle or interference. The motorcycle with the cowl was the best. The way the wind hits is completely different from the naked state.

2022.05.03

カテゴリ

タグ

Change from single horn to double horn...

[Single horn] has been changed to [Double horn]. CBX1000 models CB1 and SC03 are single horns. It's a single horn with a cowl attached to it that seems to be part of the design,but I didn't have a place to attach it,so I changed it to a small car horn.

2022.05.02

カテゴリ

タグ

CBX400F Integra cowl installation troubles...

Motorcycles with upper cowl or bikini cowl have no gaps. Also,some older models such as the GPZ900R have a gap of about 10cm between the meter and the cowl. There is also a gap in the later model of CBX1000. Ducati's bevel etc. have large gaps. It may be an intentional gap.

2022.04.28

カテゴリ

タグ

CBX400F Integra cowl reinstallation edition...

When I attached it to the CBX1000 fully open,the offset was too large and there was a gap between the CBX1000 meter and the CBX400F cowl. I was referring to the mounting position of rocket cowls such as Ducati's bevel. This is based on Kawasaki's Z1R turn signal installation position and cowl line. The fixing position of the cowl is based on Vedkati's bell.

2022.04.27

カテゴリ

タグ

GUN125-Transplanted the horn from the new Hilux...

The CBX1000 horn is quite large and heavy,probably because it is part of the design. Since it has been made into a cowl,we will replace the horn with something lighter and smaller. The horn of the Hilux has been changed. I transplanted the normal horn from the Hilux that I had removed.

2022.04.26

カテゴリ

タグ

CBX400F Integra cowl installation edition...

If you have the stay of the later model of CBX1000,SC06,you can install the frame mount cowl fairly easily. Easy to install means easy to remove.

2022.04.25

カテゴリ

タグ

FCR-tuning JN - 2022-04-23 - Video available...

Continuing from the other day,I will touch on JN. If it goes out of control in the same season and in the same place,I think it's better to think that something is broken in the first place. I work with the mindset that if something goes wrong,I can just get things back to normal.

2022.04.24

カテゴリ

タグ

FCR - tuning JN - 2022-04-22...

Regarding the FCR turning,the JN-Jet Needle's clip seems to change the way it blows up. The position of the clip is lean at the top and rich at the bottom. It's better to choose based on feel,without worrying about the air/fuel ratio.

2022.04.22

カテゴリ

タグ

Trouble installing generator rebuild...

Replace the CBX1000 regulator or generator. Even though I called it a replacement,I sent the generator to a specialized company and had it rebuilt. As shown in the video,it blows out a lot of white smoke. I realized that modifying the electrical system is an item that requires a lot of thought.

2022.04.22

カテゴリ

タグ