FCR | Page 18 | CBX-LALALA HONDA Mortorcycle CBX1000 FCR Carburetor

FCR-Fuel Level Adjustment

This is a fuel level adjustment for FCR. Can you do something like this? A story that made me want to get angry. Adjusting the fuel level means adjusting the fuel level of all 6 cylinders to the same height. Anyone can do it just by aligning the height of the fuel surface. Is the downdraft FCR about 15 degrees? Is it about 15 degrees for all FCRs? Is the horizontal about 30 degrees?

2022.06.03

カテゴリ

タグ

FCR tuning - Jet Needle - 2022-06-02...

CBX1000 FCR turning. This is a story about changing JN and changing clips after tuning in. The other day,I touched the oil level,removed the SJ,and touched it a lot,so I checked the synchronization of the 6 cylinders of the FCR once just to be sure. Honestly,it was at a level where I didn't have to touch it much.

2022.06.03

カテゴリ

タグ

FCR fuel filter

This is a story about the fuel filter used in FCR. I would like to introduce you to the fuel filter that I use. Basically,most of the cases are actual cases at CBX1000. In fact,I don't know what kind of cases will occur with other vehicles.

2022.06.02

カテゴリ

タグ

Beautiful photos - at the motorcycle exhibition hall...

I’m taking photos at the storage location for my CBX1000. These pictures are taken at the display area of the rental garage. The lighting from the fluorescent lamps and direct sunlight seems to be ideal, as the polished and chrome parts, as well as the gloss black painted parts, reflect beautifully. This creates a feel of the bike being newer than it actually is, which is very gratifying.

2022.05.31

カテゴリ

タグ

FCR Tuning - Slow jet changed from 48 to 55 - 2022-05-23...

Changed FCR's SJ slow jet. The number has been changed from SJ-48 to SJ-55. The intention is to bring the fixed AS to around 1.0 to 1.30 minutes by reversing P1.15 minutes. I've put #52 in SJ,so I'm predicting that unless I put in at least #55,AS won't be around 1.30 minutes back,so I'm raising the number all at once.

2022.05.24

カテゴリ

タグ

Heading to Hattendo Village in Mihara City,Hiroshima Prefecture for a test run of the FCR....

The other day,I replaced my MJ,so I went on a solo tour on the expressway to Hattendo Village,which also served as a test run of the FCR. Hattendo is famous for its cream bread. The facility itself seems to be kept well-maintained,and the staff seemed to be responding well. If you have a flight passing by nearby,Sehito is a facility worth stopping by at least once.

2022.05.23

カテゴリ

タグ

Jet needle clip change - 2022-05-18...

I was concerned about the blowout being about 1/2,so I changed the number of clip stages. The current FCR jet needle is 90FTR #2,and I was planning to touch the AS air screw from time to time. The vacuum gauge uses two Daytona 4-gauges to create a CBX1000-spec 6-gauge.

2022.05.18

カテゴリ

タグ

Scope of influence of FCR's MJ main jet...

I try to keep it between 11.5 and 13.5 during acceleration,and aim for 12.5 to 13.0 as much as possible. I try not to worry about it even if I get into 11 in a partial. I prioritize the experience and try not to worry about the air-fuel ratio even if it reaches a very extreme value.

2022.05.16

カテゴリ

タグ

PINGEL cock flow comparison PINGEL1/4...

I am using PINGEL4000-1/4. I don't know the model name,but I'm using a reserve type with an adapter. In rare cases,there are online shopping sites that have incorrect adapter descriptions or actual sizes. The comparison target is the CBX1000's genuine fuel cock,which is a forced open/close type fuel cock.

2022.05.13

カテゴリ

タグ

Brembo - Corsa Corta installed...

Brembo Corsa Corta installed on CBX1000. Is it better to write brembo's CorsaCorta19RCS? The caliper and master are a combination of flow rates. The front is CNC 4 pot 30/34 40mm. 4 pots with 30mm and 34mm pistons. The diameter of the master is 19.

2022.05.12

カテゴリ

タグ