June 2022 | Page 2 | CBX-LALALA HONDA Mortorcycle CBX1000 FCR Carburetor

FCR-MJ main jet purchase 36 pieces...

Currently,MJ's stock was limited to 102-128,so I purchased additional items. 6th place: 130,132,135,138,140,142. I purchased it as a POSH set. I bought a set of 6. I bought 6 pieces in a 6 piece set. A total of 36 pieces will be purchased,just the number of main jets.

2022.06.16

カテゴリ

タグ

FCR - Synchronization - Taper Gauge...

The suction force for each cylinder is slightly different,but even if you just match it with the taper gauge,the synchronization is good. Although it is far from perfect,there are two points below: (1) The engine does not idle at high speeds when it warms up. (2) The tachometer returns extremely poorly when racing.

2022.06.15

カテゴリ

タグ

FCR - SJ count tuning - tuning parts list available...

It's in the FCR manual. I bought and tried all of SJ's #35-#55. Roughly speaking,my vague conclusion is that the appropriate values for the return of the PS and AS screws will change. AS,SJ,and PS have different responsibilities.

2022.06.15

カテゴリ

タグ

FCR - turning when installing Foam Air Filter Sock...

When tuning up an FCR,you will always run into problems such as the characteristics of Foam Air Filter Sock and Velocity Stacks. Is it better to add it? Is it okay not to wear it? What are the advantages and disadvantages? This time,I would like to comment on such questions as a rider who regularly uses Foam Air Filter Socks. I don't think it's the correct answer,but I think it has credibility as an opinion or way of thinking.

2022.06.15

カテゴリ

タグ

FCR-tuning luggage minimum...

This is the item I brought out for the FCR tuning of CBX1000. Do not carry excessive tools for unexpected situations,such as diaphragms and bolts for the main jet and accelerator pump,and clips for the jet needle. It fits in a small tool box. It's for storage,so it's not very strong,but I bought it at a 100 yen shop.

2022.06.14

カテゴリ

タグ

FCR - tuning - AS Uotani SP2 ignition timing [1] - 2022-06-12...

I set this because I advanced the light dial of AS Uotani SP2 from [0] to [1]. I prefer the feeling of installing it in [2],but it's not a bad feeling with [1],so I'm thinking of adjusting the FCR turning in [1] and then changing the ignition timing to +4 degrees in [2]. I am.

2022.06.13

カテゴリ

タグ

FCR-turning Sheet-Google Sheets Spreadsheet...

How is FCR's past history managed? There are various ways to manage your information,such as using a dedicated app,a notebook,or managing it only in your memory. I have been keeping track of my history since the very beginning when I started using FCR. Even if you say that the history is kept,there are some parts that are not kept.

2022.06.13

カテゴリ

タグ

FCR - tuning - 2022-06-10

This article is about the test run and turning after changing the light dial of AS Uotani SP2. This is a tuning change due to a change in ignition timing. I was thinking of dealing with it by changing the accelerator pump or clip. However,I think it is better not to include the acceleration pump as the main tuning item.

2022.06.11

カテゴリ

タグ

AS Uotani SP2-gap adjustment and iridium plug...

AS Uotani's SP2 has instructions to adjust the plug gap to 1.1-1.3mm. I've had some doubts about that. Is the same true for iridium plugs? This was a while ago,but I would like to write about the results of a phone call I made to AS Uotani.

2022.06.11

カテゴリ

タグ

AS Uotani SP2-Dial turning...

My CBX1000 is equipped with AS Uotani SP2. The reason is not to strengthen the ignition system,but rather to avoid unnecessary trouble. Of course,it is also wonderful as an aftermarket part.

2022.06.10

カテゴリ

タグ