2022-06

FCR

FCR-turning-AS Adjustment-22/06/25...

CBX1000 FCR turning. I adjusted the AS air screw and the PS pilot screw. As I wrote in another article,my current opinion is that there are no surprising changes in PS and AS for each cylinder in the CBX1000.
2022.06.27
       
カテゴリCBX1000FCR
タグcabtuningCBX1000FCRFCR-BeginnersVacuumgauge
FCR

Verifying the impact of CBX1000 PS...

This is a blog post where I tried restoring the PS of CBX1000's FCR. PS is active when idling. It works at least at rotation speeds of 1300RPM-1500RPM. It may be that after a certain level of concentration (returning the PS) there will be almost no effect.
2022.06.27
       
カテゴリCBX1000FCRMaintenanceManual
タグASCBX1000FCRPS
FCR

pilot screw adjusting tool processing...

pilot screw adjusting tool. One of the things I always worry about when using a CBX1000 is how to turn the pilot screw. I've tried about 3 pilot screw adjusting tool so far,but I haven't been able to find the perfect one.
2022.06.27
       
カテゴリCBX1000FCRMaintenance
タグCBX1000FCRPS
FCR

FCR-Synchronous screw nut limits and SEP bearing guide...

The article says there are limits,but the article is not saying that there are limits to synchronization,but rather that if you synchronize several times,you will reach the limit of the adjustment range,so you will need to reset it. This will be a blog post. This is a story that people who don't have anything to do don't have anything to do,so please read it quickly.
2022.06.24
       
カテゴリCBX1000FCRMaintenance
タグcabtuningCBX1000FCR
FCR

FCR-Balance pipe effect

This is going to be a bit of a rough article. I've been wanting to check the operation with and without a balance pipe for a while now,so I'd like to post about that. I will write the results first. [No change] The verification method is sloppy,and I don't know if the thickness of the balance pipe is the appropriate size in the first place.
2022.06.24
       
カテゴリCBX1000FCRMaintenance
タグCBX1000FCRRamairYouTube
FCR

FCR tuning - MJ main jet change 22/06/23...

Recently,the situation has become such that instead of tuning up FCR when I have time,I make time to set up FCR. I have to either calm down a little or get over it to the point where it doesn't bother me. Although it is called a main jet change,MJ and JN were changed.
2022.06.24
       
カテゴリCBX1000FCR
タグCBX1000CBX400FFCRFCR-BeginnersJNMJ
FCR

FCR tuning-MJ or JN 22/06/20...

I couldn't help but worry about it,so I decided to leave work early in the morning and finish by noon to set up. I have no complaints about the turning,but what would happen if I changed them? I want to know. This time,MJ was changed and JN was changed accordingly.
2022.06.21
       
カテゴリCBX1000FCR
タグCBX1000FCRFCR-BeginnersJNMJ
Maintenance

FCR-Drain bolt O-ring replacement...

Drain bolt O-ring replacement for FCR33 pie. It was leaking gasoline,so I replaced it immediately. The symptoms did not improve even after replacing the chamber gasket,so I fixed it by replacing the O-ring on the drain bolt.
2022.06.20
       
カテゴリCBX1000FCRMaintenance
タグCBX1000FCRFCR-Beginners
FCR

FCR-tuning-MJ-22/06/18

I mainly tried the MJ main jet. It's not in bad condition now,and when I drove on the expressway,the air-fuel ratio was 12.5 at full throttle and partial. It is unclear whether it is accurate at full throttle because it is difficult to measure the air-fuel ratio during partial and acceleration,and it is difficult to maintain the throttle opening for a long time.
2022.06.20
       
カテゴリCBX1000FCR
タグCBX1000FCRFCR-BeginnersMJ
CBX1000

Rental Garage - CBX400F Integra Cowl Specifications...

My CBX1000 uses part of the motorcycle shop as a rental garage. I haven't taken many photos since I changed to the CBX400F Integra cowl specification. I'm honored that the motorcycle shop told me there would be no problem since it will be their signature vehicle. When returning a bicycle after riding,we make sure to wash the vehicle and remove any debris from the front before parking it in the rental garage.
2022.06.16
       
カテゴリCBX1000Cowl
タグBremboCBX1000CBX400FComstarWheelsCustomHeadcoverRepaint
Next page