user | Page 19 | CBX-LALALA HONDA Mortorcycle CBX1000 FCR Carburetor

FCR-Synchronous screw nut limits and SEP bearing guide...

The article says there are limits,but the article is not saying that there are limits to synchronization,but rather that if you synchronize several times,you will reach the limit of the adjustment range,so you will need to reset it. This will be a blog post. This is a story that people who don't have anything to do don't have anything to do,so please read it quickly.

2022-06-24

カテゴリ

タグ

FCR-Balance pipe effect

This is going to be a bit of a rough article. I've been wanting to check the operation with and without a balance pipe for a while now,so I'd like to post about that. I will write the results first. [No change] The verification method is sloppy,and I don't know if the thickness of the balance pipe is the appropriate size in the first place.

2022-06-24

カテゴリ

タグ

FCR tuning - MJ main jet change - 2022-06-23...

Recently,the situation has become such that instead of tuning up FCR when I have time,I make time to set up FCR. I have to either calm down a little or get over it to the point where it doesn't bother me. Although it is called a main jet change,MJ and JN were changed.

2022-06-24

カテゴリ

タグ

FCR tuning - MJ or JN - 2022-06-20...

I couldn't help but worry about it,so I decided to leave work early in the morning and finish by noon to set up. I have no complaints about the turning,but what would happen if I changed them? I want to know. This time,MJ was changed and JN was changed accordingly.

2022-06-21

カテゴリ

タグ

FCR-Drain bolt O-ring replacement...

Drain bolt O-ring replacement for FCR33 pie. It was leaking gasoline,so I replaced it immediately. The symptoms did not improve even after replacing the chamber gasket,so I fixed it by replacing the O-ring on the drain bolt.

2022-06-20

カテゴリ

タグ

FCR Tuning - Changed from MJ(Main jet) 125 to 120 - 2022-06-18...

I mainly tried the MJ main jet. It's not in bad condition now,and when I drove on the expressway,the air-fuel ratio was 12.5 at full throttle and partial. It is unclear whether it is accurate at full throttle because it is difficult to measure the air-fuel ratio during partial and acceleration,and it is difficult to maintain the throttle opening for a long time.

2022-06-20

カテゴリ

タグ

Rental Garage - CBX400F Integra Cowl Specifications...

My CBX1000 uses part of the motorcycle shop as a rental garage. I haven't taken many photos since I changed to the CBX400F Integra cowl specification. I'm honored that the motorcycle shop told me there would be no problem since it will be their signature vehicle. When returning a bicycle after riding,we make sure to wash the vehicle and remove any debris from the front before parking it in the rental garage.

2022-06-16

カテゴリ

タグ

FCR-MJ main jet purchase 36 pieces...

Currently,MJ's stock was limited to 102-128,so I purchased additional items. 6th place: 130,132,135,138,140,142. I purchased it as a POSH set. I bought a set of 6. I bought 6 pieces in a 6 piece set. A total of 36 pieces will be purchased,just the number of main jets.

2022-06-16

カテゴリ

タグ

FCR - Synchronization - Taper Gauge...

The suction force for each cylinder is slightly different,but even if you just match it with the taper gauge,the synchronization is good. Although it is far from perfect,there are two points below: (1) The engine does not idle at high speeds when it warms up. (2) The tachometer returns extremely poorly when racing.

2022-06-15

カテゴリ

タグ

FCR - SJ count tuning - tuning parts list available...

It's in the FCR manual. I bought and tried all of SJ's #35-#55. Roughly speaking,my vague conclusion is that the appropriate values for the return of the PS and AS screws will change. AS,SJ,and PS have different responsibilities.

2022-06-15

カテゴリ

タグ