JN | Page 5 | CBX-LALALA HONDA Mortorcycle CBX1000 FCR Carburetor

FCR tuning - MJ or JN - 2022-06-20...

I couldn't help but worry about it,so I decided to leave work early in the morning and finish by noon to set up. I have no complaints about the turning,but what would happen if I changed them? I want to know. This time,MJ was changed and JN was changed accordingly.

2022-06-21

カテゴリ

タグ

FCR - SJ count tuning - tuning parts list available...

It's in the FCR manual. I bought and tried all of SJ's #35-#55. Roughly speaking,my vague conclusion is that the appropriate values for the return of the PS and AS screws will change. AS,SJ,and PS have different responsibilities.

2022-06-15

カテゴリ

タグ

FCR - tuning - AS Uotani SP2 ignition timing [1] - 2022-06-12...

I set this because I advanced the light dial of AS Uotani SP2 from [0] to [1]. I prefer the feeling of installing it in [2],but it's not a bad feeling with [1],so I'm thinking of adjusting the FCR turning in [1] and then changing the ignition timing to +4 degrees in [2]. I am.

2022-06-13

カテゴリ

タグ

FCR - tuning - 2022-06-10

This article is about the test run and turning after changing the light dial of AS Uotani SP2. This is a tuning change due to a change in ignition timing. I was thinking of dealing with it by changing the accelerator pump or clip. However,I think it is better not to include the acceleration pump as the main tuning item.

2022-06-11

カテゴリ

タグ

FCR tuning - Jet Needle - 2022-06-02...

CBX1000 FCR turning. This is a story about changing JN and changing clips after tuning in. The other day,I touched the oil level,removed the SJ,and touched it a lot,so I checked the synchronization of the 6 cylinders of the FCR once just to be sure. Honestly,it was at a level where I didn't have to touch it much.

2022-06-03

カテゴリ

タグ

Heading to Hattendo Village in Mihara City,Hiroshima Prefecture for a test run of the FCR....

The other day,I replaced my MJ,so I went on a solo tour on the expressway to Hattendo Village,which also served as a test run of the FCR. Hattendo is famous for its cream bread. The facility itself seems to be kept well-maintained,and the staff seemed to be responding well. If you have a flight passing by nearby,Sehito is a facility worth stopping by at least once.

2022-05-23

カテゴリ

タグ

Jet needle clip change - 2022-05-18...

I was concerned about the blowout being about 1/2,so I changed the number of clip stages. The current FCR jet needle is 90FTR #2,and I was planning to touch the AS air screw from time to time. The vacuum gauge uses two Daytona 4-gauges to create a CBX1000-spec 6-gauge.

2022-05-18

カテゴリ

タグ

FCR-tuning JN - 2022-04-23 - Video available...

Continuing from the other day,I will touch on JN. If it goes out of control in the same season and in the same place,I think it's better to think that something is broken in the first place. I work with the mindset that if something goes wrong,I can just get things back to normal.

2022-04-24

カテゴリ

タグ

FCR - tuning JN - 2022-04-22...

Regarding the FCR turning,the JN-Jet Needle's clip seems to change the way it blows up. The position of the clip is lean at the top and rich at the bottom. It's better to choose based on feel,without worrying about the air/fuel ratio.

2022-04-22

カテゴリ

タグ

FCR synchronization and 6-series vacuum gauge...

Calibration and adjustment of vacuum gauge. Align the synchronization of CBX1000 with 6 vacuum gauges. If you are using a 4-way vacuum gauge,you can easily find out how much the difference is by replacing the numbers 1 and 2 that you normally use.

2022-04-11

カテゴリ

タグ