2022-08

FCR

Three advantages of converting CBX to FCR...

This time, I would like to introduce three benefits of converting CBX to FCR, which is my favorite, by converting CBX to FCR33. I will write about it in a column, but I will also introduce the disadvantages. There are no disadvantages caused by converting to FCR. Basically there are only good things.
       
カテゴリCBXFCR
タグCBXColumnFCR
CBX

Test drive the CBX and head to the rental garage...

I didn't return it to the rental garage for a while because the rainy season ended and it was easy to drive, and I was frequently tuning the FCR. The day before I ride the CBX, I pull it out of the rental garage, leave it at home, and ride it the next day.
       
カテゴリCBXCowlMaintenance
タグCBXCBX400FColumnCustomRepaint
FCR

About taper angle and FCR tuning - MJ confirmation from test run - How much does MJ influence? 22/08/20...

Since today is Saturday, I wanted to ride on the CBX, but unfortunately it was about to rain. To shake or not to rain? Anything else? It was a subtle sky pattern. I ended up doing a test drive around my house while checking the weather forecast on my smartphone. So, I will be doing a test run mainly to see how the MJ looks after changing the tuning from last time.
       
カテゴリCBXFCRManual
タグCBXColumnFCRFCR-BeginnersJNMJ
CBX

About FCR-PS. Idle port, slow port and air-fuel ratio at idling...

The other day, when I was carrying around a Carburetor Pilot Screw Adjustment Tool, a certain mass touring group asked me, ``What is this?'' ” I was bombarded with questions in turn. I have come to my own conclusions and done things that I had doubts about since I started tuning up FCR, so I will write about them historically.
       
カテゴリCBXFCR
タグASCBXColumnFCRFCR-BeginnersJNPSSJ
CBX

What is the appeal of motorcycle carburetor specifications?...

There are two types of motorcycle fuel injection systems in the world. Carburetor specifications or other than Carburetor specifications? Except for the carburetor specifications, it will be injection. Since FCR is also a carburetor specification, I will write about the good and bad points of carburetor specifications while comparing them with injection. The trick here is to write about it while comparing it to injection.
       
カテゴリCBXFCR
タグCBXColumnFCR
FCR

FCR-tuning SJ and MJ change 22/08/15...

With SJ45, I felt like the screw was opening too much, so I changed it to 42. I chose 42 because I wanted to make fine-tuned tuning, but 40 might be the perfect range for all year round. I feel a little regretful that it might not be necessary to make it look strangely deviate from Bito's initial tuning.
       
カテゴリCBXFCRMaintenance
タグASAS-Uotani-SP2cabtuningCBXFCRFCR-BeginnersJNPS
CBX

Should I change the taper angle and cut-up of FCR? Check the number of clip stages first....

This time I will write in a column. The other day, I had a little conversation about the FCR tuning with the divine engineer who gave me two engines for my CBX free of charge. I was told, ``JN checks the number of clip stages before checking the taper angle.'' According to the master, it's natural that the clip position will change if you change the taper, so if you don't take that into account when purchasing a jet needle, it will be a waste of money.
       
カテゴリCBXFCR
タグCBXFCRFCR-BeginnersJN
CBX

FCR tuning-AS air screw adjustment22/08/03...

I wanted to eat curry for lunch, so I went for a light FCR test run. With my ability, I can't decide on a good screw position in one go, so I just do test runs and try different screw positions from rich to lean.
       
カテゴリCBXFCRtouring
タグASCBXFCRFCR-BeginnersPSYoshimura
CBX

Photos of CBX cowl specifications are posted....

Even if it is not a CBX cowl specification, some parts may be helpful for owners who want to install a frame-mounted cowl on a naked specification motorcycle. This is a duplicate of the previous article, but the content posted a while after installation and the post immediately after installation are slightly different.
       
カテゴリCBXCowl
タグCBXCBX400FColumnCustomRepaint