Page 13 | CBX-LALALA HONDA Mortorcycle CBX1000 FCR Carburetor

FCR tuning - jet needle clip stage number change - 2022-10-16...

CBX1000 FCR tuning. Even though I say I will tune it,I am very satisfied with the current situation,so I am changing it for the sake of knowledge. The number of clip stages has been changed from [2] to [3]. Very good. The number of clip stages will be set to [3] for the time being. If you change the number of clip stages from season to season or over time,you will often find that the ride quality of your motorcycle changes significantly and becomes better.

2022-10-17

カテゴリ

タグ

FCR Tuning - Acceleration Pump Discharge Timing Adjustment - 2022-10-12...

The acceleration pumps of the old CBX1000 FCR are attached to numbers 3 and 6. Looking at the range of influence in the tuning manual,it is in 0.6mm increments,but there are individual differences between vehicles and FCRs. Or,the tabs may become strange due to over-adjustment,so it is better to check visually to some extent and use this as a guideline only.

2022-10-12

カテゴリ

タグ

FCR Tuning - Trial run of pilot screw Slightly rich...

I did a test run of FCR tuning and took pictures of the rear area.If anything,the story is mainly about the test run.It's around 13 when idling,and I cut it down to about 12 with partial throttle pening.

2022-10-10

カテゴリ

タグ

FCR Tuning - Change slow jet from 40 to 42 - 2022-10-08...

The other day,I changed the slow jet from 42 to 40. However,it seemed like we were reaching the limit of returning the PS,so we changed it from 40 to 42 again. For me,the boom now is to keep the air-fuel ratio at 12.5 to 13.0 when idling with the throttle fully closed. It feels like the ride becomes milder,which is good.

2022-10-08

カテゴリ

タグ

FCR Tuning - An Easy Way to Turn Off the Accelerator Pump...

All you have to do is clip the push rod of the accelerator pump to prevent it from moving. I will also add a photo,so please check the size and position of the clip. For those using the old CBX1000 FCR,there are two carburetors.

2022-10-08

カテゴリ

タグ

Amon 5-pole slim relay surge coil countermeasures...

My CBX1000 uses Amon's 4-pole relay and 5-pole relay for the added wiring part. It will be referred to as a relay below. The other day when I was browsing the internet,I found that the current flows backwards after the coil is disconnected. I did not know. The relay is used to turn on and off the position lamp.

2022-10-06

カテゴリ

タグ

FCR-PS Isn't it too rich? How to decide between pilot screw and slow jet...

I've been worried about something ever since I started using FCR. This is how to return the pilot screw. The other day,when I was synchronizing,I noticed something,so I'll write it down. There are few people who specifically write about how to decide on slow jets and pilot screws.

2022-10-05

カテゴリ

タグ

FCR tuning - Acceleration pump adjustment - If it is too fast,it will hit the throttle valve....

Write down what will hit you first. I found a case the other day,where the fuel injection from the FCR's accelerator pump hit the throttle valve. The fuel is not being sucked into the engine,but is instead hitting a door called the throttle valve.

2022-10-05

カテゴリ

タグ

FCR Tuning - Synchronization - 2022-10-03...

When I went touring the other day,I touched the AS air screw,PS pilot screw,and idling stop screw,so I thought that the synchronization might be loose,so I made time to do it from 17:00 to 18:00. I synchronized while being careful not to be unable to work due to sunset.

2022-10-04

カテゴリ

タグ

CBX400F Integra cowl installation - leftover parts for naked...

When I was cleaning up my room,I came across some parts that I haven't used recently. These are the leftover parts from CBX1000's CBX400F Integra cowl specification. Parts for naked style.

2022-10-03

カテゴリ

タグ